Rcbs Carbide Replacement Cutter for Trim Pro 3-way Cutt Manual de usuario descargar pdf

CARBIDE

REPLACEMENT

CUTTER FOR TRIM PRO

3-WAY CUTTER

LIMITED LIFETIME WARRANTY

Your Carbide replacement cutter for Trim Pro 3-Way Cutter is warranted

to be free from defects in material or workmanship for as long as the

original owner owns it. This warranty is extended only to the original

consumer purchaser. This warranty excludes any electrical components

or products. All RCBS products are intended for non-commercial use by

hobbyists. Any other use of these products will void the warranty.

Should you believe that your Carbide replacement cutter for Trim Pro 3-

Way Cutter is defective in material or workmanship, you must return the

Carbide replacement cutter for Trim Pro 3-Way Cutter to Ammunition

Accessories Inc. through its Oroville operation (hereinafter “Oroville

Operations”) postage paid for evaluation. If defective, the product will be

repaired or replaced at Oroville Operations’ option, at no charge.

Send a dated proof of purchase to Oroville Operations for return shipping

and handling, along with the Carbide replacement cutter for Trim Pro 3-

Way Cutter to:

Ammunition Accessories Inc.,

Oroville Operations

605 Oro Dam Blvd East

Oroville, California 95965

Warranty services cannot be provided without meeting the above

requirements.

THIS LIMITED LIFETIME WARRANTY DOES NOT COVER DEFECTS

OR DAMAGE RESULTING FROM: CARELESSNESS, MISUSE,

COMMERCIAL USE, ABUSE, IMPROPER INSTALLATION,

MODIFICATION, OR NORMAL WEAR AND TEAR. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS

LIMITED LIFETIME WARRANTY. OROVILLE OPERATIONS IS NOT

LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF

THE PRODUCT AND UNDER NO CIRCUMSTANCES SHALL

OROVILLE OPERATIONS BE LIABLE FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES. HOWEVER, SOME STATES DO NOT

ALLOW LIMITATIONS ON INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT

APPLY TO YOU.

The above warranty provides the sole and exclusive warranty available

to the customer in the event of a defect in material or workmanship in the

Carbide replacement cutter for Trim Pro 3-Way Cutter. This warranty

gives you specific legal rights, and you may also have other rights which

vary from State to State.

SAFETY

Reloading is an enjoyable and rewarding hobby that can be conducted

safely. But, as with any hobby, carelessness or negligence can make

reloading hazardous. This product has been designed from the

beginning with the user's safety in mind. When reloading, safety rules

must be followed. By observing these rules, the chance of a hazardous

occurrence causing personal injury or property damage is minimized.

GENERAL

• Use all equipment as the manufacturer recommends. Study the

instructions carefully and become thoroughly familiar with the

operation of the product. If you do not have written instructions,

request a copy from the equipment manufacturer.

• Do not take short cuts. Attempting to bypass established procedures

is an invitation to an accident.

• Observe "good housekeeping" in the reloading area. Keep tools and

components neat, clean and orderly. Promptly and completely clean

up primer and powder spills.

• Reload only when you can give your undivided attention. Do not

reload when fatigued or ill, or under the influence of medications or

alcohol.

• Develop a reloading routine to avoid mistakes which may prove

hazardous. Do not rush - load at a leisurely pace.

• Always wear adequate eye protection to protect your eyes from flying

particles. You assume unnecessary risk when reloading without

wearing safety glasses.

LOADING DATA

• Use only laboratory tested reloading data. We highly recommend the

current SPEER Reloading Manual.

• OBSERVE ALL WARNINGS ABOUT THE USE OF MAXIMUM

LISTED LOADS

INTRODUCTION

The Carbide replacement cutter for Trim Pro 3-Way Cutter was

designed to provide a lifetime of use and to produce clean and

consistent cutting.

DISASSEMBLY

Disassemble your existing 3-Way Cutter to remove the Standard

Cutter Head.

1. Loosen the Outside Deburring Cutter Setscrew (D) and rotate

Thumb Screw (B) counter clockwise to remove the Outside

Deburring Cutter (C) from the 3-Way Cutter Holder (A).

2. Loosen the 8-32 x 1/8 Setscrew (I) and remove the Standard

Cutter Head (E).

3. Remove the 8-32 x 1/8 Setscrew (G), 6-32 x 3/8 Setscrew

(H) and the Outside Chamfering Pilot (F) from the Standard

Cutter Head (E).

ThumbScrew

OutsideDeburring

Cutter

OutsideDeburring

CutterSetscrew

StandardCutter

Head

CarbideCutter

Head

Chamfering

Pilot

8‐32x1/8

Setscrew

6‐32x3/8

Setscrew

3‐WayCutterHolder

8‐32x1/8

Setscrew

Photo 1

ASSEMBLY

Reassemble the 3-Way Cutter with the new Carbide Cutter

Head.

1. Insert Chamfering Pilot (F), 6-32 x 1/8 Setscrew (H) and 8-32

x 1/8 Setscrew (G) into the Carbide Cutter Head (J). The 6-32 x

3/8 Setscrew (H) is used to adjust the amount of inside case

mouth chamfer. The 8-32 x 1/8 Setscrew (G) is used to secure

item the Chamfering Pilot (F). Use a sized and de-primed case,

ready to be trimmed, and place the case mouth over the

Chamfering Pilot (F).

2. Make appropriate adjustments to the 6-32 x 3/8 Setscrew (H)

to allow the case to rest on the cutting flutes of the Carbide

Cutter Head (J). Once set, remove case and apply downward

pressure to the nose of the Chamfering Pilot (F). Secure the

Chamfering Pilot (F) in place with the 8-32 x 1/8 Setscrew (G).

Ensure cutter orientation is similar to that in Figure 1. Final

adjustments will be discussed later.

3. Insert the assembled Carbide Cutter Head (J) into the 3-Way

Cutter Holder (A), ensure the back of the cutter bottoms out

against the 3-Way Cutter Holder (A) and orientation of cutter is

similar to what is shown in figure 1. Secure the assembled

Carbide Cutter Head (J) in place with the 8-32 x 1/8 Setscrew (I)

and make sure the 8-32 x 1/8 Setscrew (G) is accessible, for

adjustment, as shown in Photo 2.

4. Insert the Outside Deburring Cutter (C) into the 3-Way Cutter

Holder (A). Use case from step one, place over the Chamfering

1 2

Indice de contenidos

Pagina 1 - 3-WAY CUTTER

CARBIDE REPLACEMENT CUTTER FOR TRIM PRO 3-WAY CUTTER LIMITED LIFETIME WARRANTY Your Carbide replacement cutter for Trim Pro 3-Way Cutter is warran

Pagina 2

Pilot (F) and bottom out case mouth on the cutting flutes of the Carbide Cutter Head (J). 5. Lower the Outside Deburring Cutter (C) until it just m

Comentarios a estos manuales

Sin comentarios

Rcbs Carbide Replacement Cutter for Trim Pro 3-way Cutt Manual de usuario

Busca en linea o descarga Manual de usuario para Herramientas Rcbs Carbide Replacement Cutter for Trim Pro 3-way Cutt. RCBS Carbide Replacement Cutter for Trim Pro 3-way Cutter User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Rcbs Carbide Replacement Cutter for Trim Pro 3-way Cutt